SILICONE AND EPDM PROFILE CPI-PR

We have a wide variety of rubber profiles, hard rubber, spongy and silicone in different qualities and models. Extrusion of EPDM and silicone in different colors and hardnesses.

  • EPDM PROFILESsilicona

Exceptional resistance to aggressive environments.
 Excellent weather resistance, ultraviolet rays and humidity.
 Excellent resistance to ozone.
 Very good heat resistance
 Very good resistance to low temperatures
 Good resistance to the remaining compression and elastic recovery after an imposed deformation.

  • SILICONA PROFILES

 Silicone profiles are made of high strength silicone in a range of Shore A hardness and colors to RAL or Pantone
 Safe, does not react with most chemicals, or change the original composition.
 Nontoxic, does not let taste, therefore pollutes and impairs the products with which it has contact.
 Thermo – resistant, able to withstand temperatures from – 73 to 220ºc, retaining its elastic properties without presenting crazing, or aging.
 Elastic, with a capacity of 300 percent elongation according to ASTM D – 412.

  • OTHER MANUFACTURED BY EXTRUSION

 O-ring cord suitable for hydraulic and pneumatic sealing.
 Shaped tubes to sheath rollers or similar sections.
 Compact and spongy type half-round profiles and profiles “U” tape products are widely applicable.
 EPDM rubber seals for applications in metal cladding, PVC and wood.
 Compact low-pressure pipes for conduction of water, air, gasoline, oils, etc. With the most appropriate for each case rubber we obtain good permeability and low volume swelling.
 Profiles indicated for automotive glazing and bumpers in, profiles particularly suitable for the protection of edges and sharp corners.
 Compact profiles for applications in the construction sector.
 Spongy profiles for superior sealing in car headlights. Spongy cords from 1.5 mm to 50 mm. in diameter. For sealing packaging.
 Spongy tubes suitable for coatings and insulating sheaths for protection fluffy, isolation and control cables and premature wear.

Featured products

Loading…
  • RTJ GASKETS – TG30-TG31

    RTJ joints are indicated in applications high pressures and temperatures. They are designed to be accommodated in specific slots and flanges contact surfaces of the gasket and the flange must be carefully machined and finished. They are particularly suitable for very high pressures, up to 1000 psi. The RTJ gasket material should be a little softer than the flange itself […]

  • PTFE ROD/PIPES CPI-PTFED

    Molded rod produced by compression moulding into pure rod and filled rod (color,copper powder, glass fiber, graphite, carbon fiber,carbon powder,polyphenylene,etc) Extruded rod produced by plunger extrusion processing of suspension teflon resin into pure rods,graphite rods and glass fiber rods. Pasted rod produced by paste push processing of dispersion polymerization teflon resin. CPI-PTFED, PTFE ROD/PIPES are suitable for contact […]

  • FLANGE INSULATIONS KITS TGCD

    FLANGE INSULATIONS KITS • Flange insulation kits CPI-TGCD are typically used on offshore installations, seawater environments, chemical installations, oil refinery pipelines. • Flange insulation kits CPI-TGCD follow standards ANSI 16.5 & API 605, other standards need to provide more specifications according to our requirements. • Flange Insulation Kits CPI-TGCD consist of an insulating gasket; some insulating sleeves […]

  • PTFE TUBES

    PTFE extruded tubing is manufactured by high pressure PTFE dispense resin mixed with additive, it is extruded and sintered. According to different demands, the tubing could be opaque or translucent. PTFE TUBE is suitable for contact with food, according to the FDA CFR 21.177.1550 KEY PROPERTIES • High and Low Temperature Resistance: continuous operating temperature 70℃~+260℃. • […]

  • CPI-PTFE ST

    CPI-PTFE ST stainless steel lined  gaskets consist of a perforated stainless steel insert uniformly enclosed by PTFE. The synergy between the highly corrosion resistant PTFE mantle and the perfectly centred rigid stainless steel insert give the gasket exceptional chemical and mechanical properties preventing cold-fl ow in a wide pressure-temperature range. In extreme applications they are […]

  • O-RINGS

    O-RINGS The use of O-rings extends to many fields. The main function that characterizes this type of joint is its ability to maintain the seal, preventing the mixture of liquids and gases. They are characterized by their versatility and resistance to high pressures and temperatures. The type of elastomer used in its manufacture can vary. We can offer […]